校級實驗室借用Q&A

Q1. 我剛教育訓練完,要怎麼借用呢?

請於三個工作日繳交填寫設備借用申請單(請先不要上網預約),僅限平日借用,填完請交至【科一館121室創創辦公室】或是傳送電子檔至【創創工坊臉書粉專】(回覆時間:平日 9:00-12:00 / 13:30-16:30),審核確認沒有問題後,請聯絡助教預約借用時間(不要自己過來),記得帶名牌來。在助教監督下借用操作機台三次沒問題後,助教會告知開放線上借用權限,之後線上借用時段內可自行刷卡進入教室使用機器。

創創機台一律僅限平日借用。

FB數位製造機具工坊有助教的聯絡方式與申請單

Q2. 申請單怎麼填呢?

Ans:

  • 申請單位:系所
  • 負責人(單位主管):教授(請不要填自己或行政,他們無法承擔責任)
  • 借用事由:某某課、某某專題等
  • 借用設備:機台名稱(一張申請單最多借2台、一台機器請帶一張名牌)
  • 操作人數:1~2人
  • 借用時間:最多2個禮拜

Q3. 機台有甚麼限制嗎?

  • 3D列印機
  1. 攜帶名牌.列印時間最多從早上10點~晚上10點(最多12小時、不可過夜)
  2. 確認完第一層沒有問題才能離開
  3. 單一gcode請不要放置超過4個模型
  4. 模型不要有小於2mm的特徵
  5. 列印範圍不可超過直徑18 cm * 高20 cm
  6. 線材僅允許使用 PLA 1.75 mm
  • 雷射雕刻機
  1. 攜帶名牌
  2. 開抽風機
  3. 最大工作範圍為 60 cm * 37.5 cm
  4. 最大功率為 70 %
  5. 加工30分鐘請讓機器休息一下
  6. 不能加工超過5mm或有毒的材料
  7. 工作時借用者必須在現場,以免起火
  8. 相機確認加工位置與扳起對焦片後再開始加工
  • 3D掃描機
  1. 請勿將機器帶到沒有監視器的地方使用(機器超貴的)
  2. 務必確認所有東西都收好再移動機器

Q4. 使用完後要注意什麼嗎?

Ans:

  • 3D列印機

  1. 請將工具回歸原位(請勿造成下一位使用者的不便)
  2. 藍色膠帶如有破損請撕掉重新黏貼(勿重疊或留縫)
  • 雷射雕刻機

  1. 請將工具回歸原位(請勿造成下一位使用者的不便)
  2. 記得關抽風機
  • 3D掃描機

        務必確認蓋子關好再移動機器

Q5. 機器如果有問題怎麼辦?

        請立即通知助教,並大概說明發生了什麼事(助教不會通靈)

借用時請注意素質,不要造成下一位使用者的不方便

如有違規且屢勸不聽者,酌情懲罰取消門禁2~4週

 

ICT FAQ

1. After completing the training, how can I use the machine?

    Please hand in the Equipment application form 3 Working Days before use (Do not apply online) to 【SA121】or email it to 【ICT facebook fanpage】(Response time: Weekdays 9:00-12:00/13:30-16:30). Equipment is only allowed to be used during weekdays.  After approval, you can contact the TA to make a reservation (Do not come over by yourself). When you come, please remember to bring the name tag.After operation approval under the supervision of the TA (3 times or more), TA will grant the independent user access and you are welcome to use during normal hours.

Equipment in ICT is only allowed to be used during weekdays.

    ፠The equipment application form and TA′s information can be found in the FB group數位製造機具工坊

2.How to fill in the application form?

  • Department: Your department
  • Officer in charge: Professor (Not yourselves or administration staff
  •  Purpose: which class, which project, etc (only for teaching and research, not for commercial use)
  • Equipment: Atom, Beambox, etc. (1 application form can allow at most 2 machines, and 1 name tag for 1 machine)
  • Users: 1~2 people
  • Loan period: 2 weeks at most.

3.What is the regulation on operating the machines?

  1. Bring your name tag
  2. Building time from 10 AM~10 PM (12-hour continuously printing at most, and overnight printing is not allowed)
  3. Leave only after your first layer is good.
  4. More than 4 models in 1 Gcode is not allowed.
  5. Features in the model must be bigger than 2 mm.
  6. Do not exceed the maximum working limitation: 18 cm (diameter) * 20 cm (height).
  7. Only 1.75 mm PLA  filament is allowed.
  • Beambox Laser Engraving Machine
  1. Bring your name tag
  2. Turn on the exhaust fan
  3. Do not exceed the maximum working limitation: 60 cm * 37.5 cm.
  4. Do not exceed the 70% of the maximum laser power.
  5. Rest the machine every 30 minutes.
  6. Material thicker than 5 mm or toxic is not allowed.
  7. Users should be on present on site during the operation.
  8. Check the working area with the camera and pack up the focusing ruler.
  • 3D Scanner
  1. Do not bring the machine out of monitoring area (The machine is extremely expensive)
  2. Make sure to pack the machine up in a safe place before moving.

4.What should I do after finishing the work?

  • 3D Printer
  1. Put all the tools back in place.
  2. Re-taping the platform if damaged (Do not overlap or leave a gap)
  • Beambox Laser Engraving Machine
  1. Put all the tools back in place.Turn off the exhaust fan
  • 3D Scanner
  1. Make sure to close the box before moving.

5.During the operation, what to do if anything happens to the machines?

       Please contact the TA immediately regarding the problem.

 

Mind your manners, do not cause inconvenience to the next user

In case of violation, your access will be revoked for 2~4 Weeks